Plumbing 101: A Necessity for Installing a Bathtub
Plumbing 101: A Necessity for Installing a Bathtub
Blog Article
Here below you might get more first-rate help and advice with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is also a reasonably tough job. If the old tub is easily available, the task can move speedily; if you have to open up a wall to get rid of the old tub as well as position the new bath tub, the task is much harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to leave the old bathtub as well as set in the new one. Make sure you have certified on your own for the work and fit trying it. As opposed to working with a specialist to take control of a halfway-completed project, it is better to take into consideration employing one before you start. Chances are you might need a professional plumber to make tube links.
This short article will aid you install a new bath tub in your restroom if you have actually currently purchased a new bathtub as well as do not require to change the plan of your previous water supply pipes.
Your tools and material checklist should make up the following:
Planning for the Setup
Firstly, the supporting framework provided with the bath must be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome because of the limited access that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will come from the pipelines. Once the supply pipes have been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of both wood boards under its feet, position the bath tub in the required position. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small points.
The next goal is to make certain that the tub is leveled all round. This can be attained by checking the spirit level and readjusting the feet on the tub till the spirit level reviews level.
To install taps, fit all-time low of the outermost versatile faucet connector to the ideal supply pipeline by making a compression join; then do the exact same for the various other tap.
Activate the water system and check all joints as well as brand-new pipework for leakages and tighten them if needed. Fill the tub as well as additionally inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the tub needs to wait till the tub has been utilized at the very least once as this will resolve it right into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in location between the tap as well as the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap adapters. The former type must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture an inflexible seal, causing the water to pass through the wall surface between the bath and also the tiling, causing issues with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealant can crack rather very early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that write up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while scouting around the search engines. Sharing is good. Helping others is fun. Thanks for taking the time to read it.
Request Free Estimate Report this page